What Is a Closed-Cycle Gas Turbine? | Working of Closed Cycle Gas Turbine | Components of Closed Cycle Gas Turbine

What Is a Closed-Cycle Gas Turbine?

Closed-cycle gas turbines can be defined as gas turbines, which removes the drawbacks of open-cycle gas turbines. In thises type of turbine, the air is continuously circulated within the gas turbine with the help of a compressor, heat chamber, gas turbine, and cooling chamber. The ratio of pressure, temperature, and air velocity will be constant in this type. It performs a thermodynamic cycle, which means that the fluid is circulated and used continuously without leaving the system.

A closed-cycle gas turbine diagram is very simple and includes components such as a compressor, heat chamber, and gas turbine. The generator, compressor, and cooling chamber are powered by a gas turbine. Its picture is shown below.

• The gas is compressed in the compressor.
• Compressed gas is heated in a heating chamber.
• Gas turbine helps in generating electricity.
• Electricity is generated by the generator using a gas turbine.
• The cooling gases passing from the turbine are cooled in the cooling chamber.

The closed bicycle gas turbine is an extended version of the open cycle gas turbine. Coolers are added to the open cycle gas turbines to make them closed cycle gas turbines.

A closed cycle means that the fluid used in this cycle will be used in a cyclic manner repeatedly and will not be released into the atmosphere. The working fluid in this cycle will be in gaseous form. Commonly used liquids are air, argon, helium, etc.

Also, Read: What Is the Open Cycle Gas Turbine? | Working of Open Cycle Gas Turbine | Components of Open Cycle Gas Turbine

Working of Closed Cycle Gas Turbine:

#1. Isentropic Compression

Let’s assume air is the working fluid. When the air enters the compressor, the air will be compressed. Due to compression, the pressure & temperature will increase, but the entropies will remain constant.

In the P-V diagram, the pressures (P) will increases from P1 to P2, & the volume will decreases from V1 to V2 due to compression.

In the T-S diagrams, the temperature (T) will increase from T1 to T2, and the entropy will remain constants as it is an isentropic process.

#2. Constant Pressure Heat Addition

From 2 to 3, compressed air from the compressors will enter the burner. In the burner, the external fuel provides in the combustion chamber will mix with air, & the mixture will burn inside the combustion chambers after mixing with each other.

After burning, the temperatures will increase, & the expansion of air will occur at constant pressure. SO in the combustion chamber, constant pressure heat addition will occur.

In the P-V diagrams, the pressure (P) will remain constant, & the volume will increase from V2 to V3.

In the T-S diagram, the temperatures (T) will increase from T2 to T3, and the entropy will also increase from S2 to S3.

#3. Isentropic Expansion

This process will be the opposite of processes 1-2. The heated air from the burners or combustion chambers will reach the turbine, & the air will expand inside the turbine, & some work will be done due to expansion.

This process will be an isentropic process, & no heat will be transferred during this process. In this process, the volume will increase due to expansion, and pressure will decrease.

In the P-V diagram, the volumes (V) will increase from V3 to V4, & pressure (P) will decrease from P3 to P4.

In the T-S diagrams, the temperature (T) will decrease from T3 to T4, and the entropy (S) will remain constant as it is an isentropic process.

#4. Constant Pressure Heat Rejection

This process is the opposite of processes 2-3. In this process, the hot air from the turbine is again cooled and brought to its initial state so that it can be used again.

In the P-V diagram, the pressures (P) will remain constant, & volume (V) will decrease from V4 to V1.

In the T-S diagrams, the temperature (T) will decrease from T4 to T1 due to cooling, and entropy (S) will also decrease from S4 to S1 due to heat rejection.

Also, Read: What Is a Pelton Turbine? | Working of Pelton Turbine | Parts of Pelton Turbine | Important Angles to Consider in Pelton Turbine

Components of Closed Cycle Gas Turbine:

#1. Compressor

In the compressors, the isentropic process will be carried out, i.e., the process will be adiabatic & reversible. No heat will be transferred during thises process.

#2. Burner or Combustion Chamber

After passing through the compressor, air will enter the burner or A. Combustion chamber. In this burner, a constant pressure process will occur. The pressure will remain constant, but the temperature will increase as the heat increases, and the volume will also increase.

#3. Turbine

When the hot air from the combustion chambers will reach the turbine and strike the blade of the turbine, the air will expand, & the turbine will rotate. This expansion of air in the turbines will be an asynchronous process.

The turbine is connected to the turbine with a shaft. Both the compressor and the turbine have the same shaft. When the turbine rotates, it also transfers its power to the compressor and helps it to rotate. The turbine also transfers its power to some tributaries.

The turbines are connected to a generator through a coupling. As the turbine rotates, the generator will produce electricity using the work done by the turbine.

#4. Cooler or Pre Cooler

After working in the turbine, the air is sent to the cooler. The cooler will cool the air to return to its original or initial state. The cooling process in the cooler will be carried out under constant pressure.

Also, Read: Gas Turbine Parts and Functions | Introduction to Gas Turbine Power Plant | Major Parts of Gas Turbine Power Plant | Gas Turbine | The Compressor of Gas Turbine Power Plant | Thermodynamic Cycle of Gas Turbine Power Plant

Working Principle of Closed Cycle Gas Turbine:

The closed-cycle gas turbines working principle is based on the Bretton cycle or the Joule cycle. In this type of gas turbine, a compressor is used to compress the gas isotropically, and the resulting compressed gas flows into the heating chamber. A rotor-type compressor is preferred in this turbine.

An external source is used to heat the compressed air and then passes over the turbine blades. When the gas is flowing over the top of the turbine blade, it expands and is allowed to enter the cooling chamber and cool down. The gas is cooled using the circulation of water under constant pressure at its initial temperature.

• Again, gas is passed into the compressor, & the process is repeated.
• In these turbines, the same gas is circulated repeatedly.
• The complexity and cost of the system will increase if the fluid/medium used in the turbine is other than air. This can cause problems and is difficult to solve.

Also, Read: Parts of Babcock and Wilcox Boiler | Working of Babcock and Wilcox Boiler | Specifications of Babcock and Wilcox Boiler

Difference Between Open Cycle and Closed Cycle Gas Turbine:

The heat source, the type of fluid used to operate, the circulating air, the capacity of the turbine blades, the cost of maintenance and installation, etc., differentiate between open cycle and closed gas turbines. The main difference is the circulation of the working fluid.

Also, Read: Parts of Benson Boiler | Working Principle of Benson Boiler | Construction of Benson Boiler

Advantages of Closed Cycle Gas Turbine:

Closed-cycle gas turbine advantages are

• In a closed-cycle gas turbine, turbine blades erode due to contaminated gases, and dusting leads to fouling of the compressor blades. Therefore the life of the turbine and compressor is extended.
• There is no atmospheric back pressure on the turbine exhaust like an open cycle gas turbine in a closed cycle.
• In a closed-cycle gas turbine, there is no need to filter the air coming into the compressor.
• Working fluid densities can be maintained high by increasing the internal pressure range. Therefore, compressors and turbines are small for their rated output.
• Lower oil or solid fuel can be used because direct heating is done in a closed-cycle gas turbine. These fuels are of very low cost. Therefore the process is more economical.
• It has a high output and efficiency.
• Maintenance costs are low.

Also, Read: Parts of Cornish Boiler | Working Principle of Cornish Boiler | Construction of Cornish Boiler

Disadvantages of Closed Cycle Gas Turbine:

Closed-cycle gas turbine Disadvantages are

• Due to the high internal pressure in the system, all the components used have complex designs that increase the cost significantly.
• Its response to differential load is worse than that of an open cycle gas turbine.
• It requires very large heat exchangers because, indirectly, the working fluid is heated.
• An additional component pre-cooler is added to the closed cycle gas turbine, which requires a significant amount of cold water.

Also, Read: Parts of Lamont Boiler | What Is Lamont Boiler? | Working of Lamont Boiler | Construction of Lamont Boiler

Applications of Closed Cycle Gas Turbine:

The closed-cycle gas turbine application includes the following.

• They are used in the generation of electric power.
• They are used in many industrial applications.
• They are used in marine propulsion, locomotive propulsions, and automotive propulsion.
• They are used in aviation to provide power to jet Propulsion.

Also, Read: Keyless Remote Battery Is Low | When Does Key Fob Battery Replacing Replacing? | How to Replace a Keyless Remote Battery

---

Frequently Asked Questions (FAQ)

What Is Closed Cycle Gas Turbine?

A closed-cycle gas turbine is a turbine that uses a gas (for example, air, nitrogen, helium, argon, etc.) as a working fluid as part of a closed thermodynamic system.

A Closed Cycle Gas Turbine Works On

The closed cycle gas turbine works on the basis of the Brayton cycle or Joule’s cycle. Gas is compressed isentropically in this type of gas turbine by a compressor, which then flows into a heating chamber. Rotor-type compressors are preferred in this type of gas turbine.

Difference Between Open Cycle and Closed Cycle Gas Turbine

In an open cycle gas turbine, the gas, after rotating the turbine, is exhausted into the atmosphere. In a closed cycle gas turbine, the gas, after passing through the turbine, is not exhausted into the atmosphere but instead passes into the cooling chamber.

Thermal Efficiency of Closed Cycle Gas Turbine

The promise of efficiency of over 50 percent (when operated in a binary cycle mode) makes the closed-cycle gas turbine an attractive power conversion system candidate as the goal of power production through a sustained fusion reaction in a confined plasma is realized.

---