Important Point
Working of Constant Mesh Gearbox
- Since the gear of the main shaft is in a continuous mesh with the appropriate gear of the continuous shaft, the selection of 1, 2, 3, 4, and reverse gears is achieved with the proper pair sliding and traps of the dog clutch.
Different gear ratios in Constant Mesh Gearbox
There are Five Gear types of this Constant Mesh Gearbox
- First gear
- Second gear
- Third gear
- Fourth gear
- Reverse gear
#1. First Gear
- It is the gear that provides the maximum torque and minimum speed to the final output shaft that helps the vehicle move from its initial position when the driver selects one gear by pushing or pulling the gear lever, and the dog is in the clutch.
- It is paired with the same pair. The gear, the smallest gear on the main shaft and the largest gear on the main shaft, slides right or left over the remaining main shaft and makes contact with the forged pair, and finally receives one gear.
#2. Second Gear
- This gear provides higher speeds and lower torque than the first gear and is achieved by sliding right or left towards the corresponding dog clutch towards the appropriate pair of forged gears, the second the shorter shaft gear, and the second-largest main.
- The shaft is gear—contact with the pair.
#3. Third Gear
- This is the second-highest speed gear, with very low torque, and is achieved by sliding the right or left side of the respective dog clutch towards the appropriate pair of forged dogs, i.e., the second largest carry shaft gear and the second smallest main shaft gear.
#4. Fourth Gear
- It is the highest-speed gear of a 4-speed manual transmission in which the maximum output of the clutches shaft is transmitted to the final output by sliding the dog clutch to the right or left to create the maximum contact with the left shaft and the smallest gear.
- Is. The gear of the main shaft and very low torque, and the highest speed are obtained.
#5. Reverse Gear
- This is the gear that reverses the direction of rotation of the output shaft to move the vehicle in the reverse direction; this is achieved with special gears known as idler gears, which when the reverse shaft has selected.
- The clutch of the dog mounted between the left shaft and the main shaft makes contact with the idler gear and the reverse gear is obtained.
What is a Constant Mesh Gearbox?
- Constant-mesh gearboxes were invented to overcome the limitations of sliding mesh gearboxes. In this gearbox, all gears are always forged.
- The gear remains fixed and does not slide like a sliding mesh gearbox. In this gearbox, the sliding mesh was paired with continuously added gears, and new shifting devices called dog clutches were introduced. A continuous mesh gearbox typically comes with a 4-speed 1-reverse manual transmission configuration.
- This gearbox consists of various parts such as a countershaft, main shaft, clutch shaft, gear, and dog clutch. The gears on the coupler shaft are fixed to it and the gears on the main shaft are free to rotate. Helical and herringbone gears are commonly used in this gearbox, so it is quieter than a sliding gear gearbox that uses spire gears.
- In this gearbox, all the gears of the main shaft and countershaft are always connected with each other. Different transmission ratios or speed ratios are obtained using the dog’s clump. Dog clutches are attached with gears on the main shaft to achieve the desired speed or torque.
Construction of Constant Mesh Gearbox
- The output of the engine is done by a clutch shaft.
- The gear lay in the clutch shaft is in continuous mesh with the gear of the shaft.
- The lift shaft has five gears, one of which is connected to the gear of the clutch shaft, and the other four are connected to the gear of the main shaft.
- All four gears are of different sizes to achieve different gear ratios.
- An idler gear exists between the gear of the main shaft and the gear to form the reverse gear.
Working on Constant Mesh Gearbox
- Different gear ratios are obtained when the dog clutch is fitted with different gears of the main shaft because the main shaft is always paired with gears of gear counters of different gear ratios.
- If the dog clutch is not in contact with any gear of the main shaft, the gear of the main shaft rotates freely and does not rotate the main shaft as they are connected to the main shaft using bearings.
- The main shaft rotates only when a clutch of the dog is attached to any of the gears of the main shaft.
- The reverse gear is obtained in this gearbox using the same technique that was used in sliding the gearbox, i.e., using the idle gear between the main shaft gear and the countershaft gear.
Also, Read: What Is a Comparator | Types of Comparators
Advantages of Constant Mesh Gearbox
- Different gear ratios are obtained when the dog clutch is fitted with different gears of the main shaft because the main shaft is always Constant mesh gearboxes are quitter as helical, or herringbone gears can be used instead of a spur gear in this gearbox.
- Since the gears are attached to the dog clutches, if there is any damage while entangling the gears, the members of the dog unit are damaged, not the gear wheels.
Disadvantages of Constant Mesh Gearbox
The disadvantages of a constant mesh gearbox are as follows.
- With the slight vibration that occurs during the engagement of the dog clutch with the gear on the main shaft, it is advisable to use a synchronizer, which can reduce the effect of vibration.
- The biggest disadvantage of the double dusting constant mesh gearbox was already mentioned above.
Also, Read: How Do Aircraft Brakes Work | How Aircraft Brakes Work | Brake Design | Aircraft Brakes
Application of Constant Mesh Gearbox
- The constant-mesh gearbox was mainly used in farm trucks, motorbikes, and heavy machinery. It is also used in cars like the Ford Model T.
- Prior to the introduction of the synchromesh gearbox in 1928 by General Motors, a constant mesh box was used in motorbikes.
Frequently Asked Questions (FAQ)
Constant Mesh Gearbox
The constant gear gearbox used worm gears for power transmission. The gears are rigidly fixed on the pitch shaft. The output shaft gears rotate freely without engaging the shaft, so they do not transmit power. The gears on both shafts always mesh together.
Constant Mesh Gear
Since the gears in a constant mesh gearbox are constant mesh, they are less likely to damage the gear teeth and there is usually less gear wear.
Constant Mesh Gearbox Working
Working Principle of Constant Mesh Gearbox: The Sliding Mesh Gearbox uses Spur Gears for the transmission of power from the engine shaft to the main shaft, whereas the Constant Mesh Gearbox uses helical gears. This system generally consists of 3 shafts, i.e., the Clutch shaft, the layshaft, and Main Shaft.
Advantages of Constant Mesh Gearbox
Because the gears in a constant-mesh gearbox are constantly meshing, it’s less likely to damage the gear teeth, and there’s typically less wear on the gears. If a driver makes a “bad” change in gears, any damage that may occur will be limited to the dog clutch.
Like this post? Share it with your friends!
Suggested Read –
- Dog Clutch Transmission
- What Is a Comparator | Types of Comparators
- Lancashire Boiler | Lancashire Boiler Diagram | Steam Boiler Working Principle | Steam Boiler Parts and Function
- What Is Forming | Types of Forming | Forming Process in Manufacturing | Metal Forming Processes | Forming Operations
- What Is Boliler? | Types of Boiler | Steam Boiler | How Boiler Work | Boiler Operation | Boilers Diagram | How Does a Steam Boiler Work
- What Is Sigma Comparator | Construction of Sigma Comparator | Applications of Sigma Comparator | Advantages of Sigma Comparator | Disadvantages of Sigma Comparator
Leave a Reply